Skip to Content
Power MetersSmart Meter RP3

User Operation Manual: Smart Meter RP3

1. About Your Smart Meter RP3

The Smart Meter RP3 is an intelligent IoT meter designed to accurately measure your electricity consumption. It offers real-time insights and convenient management of your utility services.

2. Important Safety Information

Please read and understand these safety guidelines before operating your meter.

2.1 Safe Use of the Meter

  • Professional Installation: Your Rokswood Group meter should only be installed and serviced by qualified personnel. Do not attempt to open or modify the meter yourself.
  • Environmental Conditions: Ensure the meter is installed in a location that meets the recommended environmental specifications (temperature, humidity). Avoid exposing the meter to direct sunlight, extreme heat, or excessive moisture.
  • Physical Damage: Protect the meter from physical impact or damage. If the meter appears damaged, contact Rokswood Group support immediately.
  • Children and Pets: Keep children and pets away from the meter to prevent accidental damage or tampering.

2.2 Ensuring Equipment Safety

  • Authorized Repairs: Any repairs or maintenance must be performed by Rokswood Group authorized technicians.
  • Cleaning: To clean the meter, use a soft, dry cloth. Do not use abrasive cleaners, solvents, or water directly on the meter.
  • Cable Integrity: Periodically inspect any visible cables connected to the meter for signs of wear or damage. If any damage is observed, contact Rokswood Group support.

3. Getting Started

3.1 Meter Overview

  • Display Screen: The display shows current readings and credit balance.
  • Indicator Lights: [Describe the meaning of different light statuses, e.g., power on, network connectivity, low credit.]

3.2 Understanding Your Readings

Your meter provides real-time data on your consumption.

  • KWh: Your meter measures power in KWh.
  • Current Reading: This shows your total accumulated consumption and can be viewed on the meter’s display screen or in the Rokswood Utility Mobile App.
  • Credit Balance: For prepaid meters, this displays your remaining credit and can be viewed on the meter’s display screen or in the Rokswood Utility Mobile App.

4. Recharging Your Meter

Keeping your meter topped up is essential for uninterrupted service. Rokswood Group meters primarily support two recharging methods: remote connectivity and token-based.

4.1 Remote Recharge (Most Common)

Most Rokswood Group meters are designed for convenient remote recharging. Once you have purchased credit through our authorized channels (e.g., mobile app, web portal), your meter will automatically update its credit balance via its network connection.

  • How it Works: After a successful purchase, the credit is sent directly to your meter over the air.
  • Confirmation: You’ll typically receive an SMS or in-app notification confirming the successful recharge.
  • Automatic Update: Your meter’s display should update within a few minutes to reflect the new credit balance.

5. Important Note for Battery-Powered Meters and Sleep Cycles

The Smart Meter RP3 is not battery-powered and is always online, meaning recharges are always instant.

6. Troubleshooting Common Issues

6.1 Meter Not Displaying New Credit After Recharge

  • Remote Recharge:
    • Check Network Connection: Ensure your meter has a strong network signal. Look for the network indicator light.
    • Wait a Few Minutes: Sometimes, it can take a few minutes for the credit to propagate to the meter.
    • Verify Purchase: Confirm your recharge was successful through your Rokswood Group app, web portal, or SMS confirmation.

6.2 “Low Credit” or “Disconnected” Indication

  • Recharge: Your meter likely has insufficient credit. Recharge your meter following the instructions in Section 4.
  • Network Issues: If you’ve recharged and the issue persists, there might be a network connectivity problem. Check your network indicator light.

6.3 Meter Not Responding

  • Power Supply: Check if the power supply is connected and functional.

7. Frequently Asked Questions (FAQs)

  • How do I check my current credit balance?
    • You can view your credit balance on the meter display or through the Rokswood Group app/portal.
  • What happens if my credit runs out?
    • Your electricity supply will be disconnected until you recharge your meter.
  • Can I monitor my consumption history?
    • You can access your consumption data through the Rokswood Group app/portal.
  • Who do I contact for support?
    • Please refer to Section 8: Customer Support.

8. Customer Support

For any issues, questions, or technical assistance, please contact Rokswood Group Customer Support:

Last updated on
Smart Meter RP2Smart Meter RW1